Monthly Archives: February 2021

  • 0

Step by Step Process to Clean Pollen from Pool Water

Tags : 

Pollen settling on the surface of your pool water can make your pool look like something from a zombie apocalypse movie. Let’s take a look at what you can do to get rid of it.

The most important thing at this stage is to understand the following points. It is not very difficult to get rid of, as long as you work on it a little every day, during the periods when the pollen is abundant.

1. Operate your filtration

Most of the time, it is not necessary to run your filter 24 hours a day, 7 days a week. But when you have a pollen problem, the filtration system is your best defense in removing it from the surface of the water.

If necessary, put it on forced and continuous, the time to skim the surface. This may not be enough, but it is the first instinct to adopt.

As the pollen deposit is subjected to the sandstones of the wind, it may also be necessary to temporarily modify the direction of the water jet from the discharge nozzles. The idea here is to reach the dead zones of the basin to force the pollens to go towards the skimmers.

Do not forget to open the skimmer valves to 100% and the bottom drain to 50% if there are bottom deposits.

This will greatly reduce the amount of manual labor required to rid the pool of this pollen.

Of course, throughout this phase, check the state of the pressure of the filter (manometer) and the amount of waste in the baskets of the skimmers or the pump pre-filter. Clean them as soon as they are too dirty.

2. Skim the water regularly

Every morning (and maybe the afternoon too), take a very fine-meshed landing net and put it in the water to collect the pollen that has accumulated overnight.

Unfortunately, you will have to repeat this process more than once a day during periods of high pollen distribution.

Remember that an ordinary landing net is generally not as effective as its mesh/braiding is often too large to trap pollen.

At a minimum, you have to push as much pollen as possible into the water flow that goes from the delivery nozzles to the skimmers. Without forgetting to clean the water line if necessary.

3. Aluminum sulphate

Some pollens are simply too small to be captured by a dip net. They will even pass through the filtration system and return to the pool.

To get rid of this type of pollen, you can add aluminum sulfate to your water. It has the effect of clumping the pollens together to form a thicker substrate.

The filter and the landing net can thus capture them more easily. The landing net allowing them to be completely removed from the filtration circuit.

4. Shock the pool

When fighting pollen, it’s a good idea to shock the pool at night, before going to bed.

It will kill whatever has made your pool a good place to call home, because of the pollen floating around in the water.

With the filtration working continuously overnight (if you leave it running – recommended) or restarting it the next morning, you will be able to more easily remove whatever is left in the water.

5. Vacuum if necessary

Sometimes simple surface skimming and continuous filtration are not enough. If the pollen is particularly heavy in your area, you may need to vacuum the pool manually.

Do this as a last resort and only if necessary, so as not to consume water and electricity unnecessarily.


  • 0

How to Keep Your Pool Clean and Healthy with Chlorine

Tags : 

Keeping your pool clean and healthy should be the entire point of regular pool maintenance. And that pool that looks so great week in and out, is an absolute delight to the pool owner.

The most common solution to achieve this is a regular treatment of the pool water to remove lime and debris.

Ceramic tile with a heavy build up

However, the wrong dosage of cleaning products can lead to the accumulation of several layers of limestone on the walls and in the pool’s bottom. To remove this debris, you need to understand everything that can make them appear.

The Importance of Chlorine for the Pool

Chlorine is the first choice for maintaining healthy pool water. Chlorine has been used for years in swimming pools around the world.

It is a highly reactive chemical that reacts with all kinds of biological impurities in water.

If these organic impurities are not treated with care, bacteria can develop algae or even a bio-film.

What Happens if a Swimming Pool is not Well-balanced?

If the pool water has a high calcium hardness or other debris, this can cause technical problems. Like fouling or lime in the pipes and in the pool itself.

As a result, the maintenance and cleaning of the pool will increase. If the supply water is very hard, large amounts of lime can deposit on the sides of the pool.

Even if there is only a little calcium carbonate in the water, and following an unbalanced addition of chlorine and PH, lime will form at the level of the evaporation line of the water as well as on the pool walls. These lime deposits at the edge of the pool are often difficult to remove and involve manual work.

Water Filtration Rings: Less Effort, Less Cost

Compared to the maintenance consequences described above, the solutions seem incredibly simple.

The main configuration of a swimming pool is always the same. There is a filter system, a pump, and maybe a heating element, that’s all.

In accordance with the size of the pool, you must install a ring at the freshwater supply line and another ring in the circulation line. In the case of a large public swimming pool, install in the circulation line of each swimming pool, to get the same results in all swimming pools.

What’s the result?

In case of calcium hardness, the ring keeps the dissolved calcium in the pool water, which will have a more fluid texture. Over time, the pool water will be much softer, despite the calcium.

Less crust will form on the evaporation line. And limestone debris will be much easier to remove. When you use these filters and rings, you are also fighting the growth of algae in the pool.

Many owners have stopped using chemicals since the installation of these rings.

No chlorine or other pool chemicals. Without having problems with water quality.

I would not recommend such a thing for a public pool. If countless visitors use this pool, the risk would be too great. I am sure the regulatory authorities would not agree.

However, it is preferable to use these rings even for public swimming pools in order to reduce maintenance costs for protecting pipes or walls of the swimming pool. By doing this, you will need a lot less chlorine to disinfect the water than before while maintaining the same quality of water.


  • 0
calcium removal calcium killer

How to Get Professional Pool Calcium Removal Service

Tags : 

Calcium is good for your body. But when it comes to your pool, that’s a whole different story.

In case you don’t know what that story is, this is it: Not good for your pool. So, what do you do in a situation where your pool is overrun with deposits of calcium (also known as limescale)?

They’re whitish and look rather unsightly on your pool tiles. They could even be dangerous for your body when you swim in the water.

If lime develops in your pool, hire pool maintenance professionals to inspect and clean up debris from its surfaces. Most pool cleaning services make a diagnosis for the localization, as well as the elimination of limescale.

If you want to do it yourself, read the rest of the article.

Why is having lime in your swimming pool a problem?

If pool owners hunt limestone like this, it’s not for nothing! Having excess lime in your swimming pool can indeed be the cause of various problems.

First of all, at the level of the interior of the basin. Because the more our pool is loaded with limestone, the more “chance” we have of seeing it build up from the inside.

And this as well at the level of the waterline as at the level of the walls and the bottom (especially if one has opted for a swimming pool liner as a coating). And a scaled pool is a pool whose water will be cloudy, and whose walls will be covered with gray or whitish deposits.

Stains which, besides being unsightly, will promote the appearance of ‘impurities and algae development. Without forgetting the possible inconvenience for swimmers: possible irritation of the skin and eyes.

But that’s not all: having too much lime can also be dangerous for the filtration system of the swimming pool. Indeed, when there is too much lime in our water, it will simply build up scale and prevent the proper functioning of the swimming pool filter.

So how do you know if your pool contains limestone?

Look for white or light gray spots on the sides and bottom of the pool, as well as the edges of the pool deck. Limestone forms scaly spots or streaks when the pH of the pool water and the calcium levels in the water are out of balance.

Although this build-up of lime can be removed, it can be difficult to do so. This article provides homeowners with tips that any pool maintenance company wouldn’t want you to know to remove lime deposits from the pool walls and prevent their return.

Types of Calcium that Leave Deposits

There are 2 common types of calcium that form lime in a pool: calcium carbonate and calcium silicate. It is important to understand which type harms the walls of your pool.

The calcium carbonate is white, scaly and easily detached. Calcium silicate is slightly gray and more solid, which makes it more difficult to remove.

If the walls of your pool contain calcium silicate, the scale on the walls of your pool is a symptom of a more serious problem: calcium scale in the plumbing and filtration system. This is a problem that only a professional pool maintenance company can deal with.

If you don’t know what type you have on your pool, use a dropper to pour muriatic acid on the deposits. Calcium carbonate will foam in reaction to acids. Calcium silicate, being a more solid substance with robust construction, will remain unchanged.

Removing Calcium Carbonate

If your pool contains calcium carbonate, removing it is easy, but takes time.

You can use a rough but harmless object for tiles such as a wet pumice stone or an eraser to flake off deposits.

You can also get calcium descaling treatment solutions from a pool service company or a pool supply store. Follow the product instructions to avoid damaging the pool water or injuring yourself.

Removal of Calcium Silicate

Calcium silicate is incredibly difficult to remove on your own. You can try using a pumice stone, but it will take a ton of elbow grease and time to complete the process successfully.

If you have a vinyl or fiberglass pool, this will not work at all. Even some descaling treatments can take months to break down the lasting calcium silicate.

You will probably need to hire pool maintenance professionals to remove lime build-up if you cannot do it yourself. They can also adjust the quality of your pool water, including pH and calcium levels, to prevent future buildup.

Remove limestone with a blowtorch and a polishing machine

If you have emptied your pool to clean it and you notice traces of lime, there are two methods that can get rid of this debris. These methods are effective but can take a long time depending on the size of your pool.

To remove the lime that is in the walls of your pool, just use a blowtorch to make the tartar less robust and then rub it with a wire brush. With the effect of heat, the tartar will be easily removed.

If you have limestone at the bottom of the pool, simply clean the pool thoroughly with a vacuum cleaner, then sand it with sanding and polishing machine.

Once descaling and polishing are finished, rinse your pool with a Kärcher to remove debris. Then evacuate your pool, let it dry, and fill it again if you want to reuse it.

If you do not want to fill it immediately, choose a tarpaulin or a protective cover. Your pool will therefore remain intact and ready to be filled at any time you wish.

Good to know

The disadvantage of chlorine is that it makes no difference between organic impurities and the human body. The consequences after a long stay in the water are red eyes, caused by chlorine. This is the reason why most people wear swimming goggles.

You easily get rid of the limescale (or calcium deposits) and their dangerous effects on the skin and eyes so you can use your pool without worry. All you have to do is call a professional pool calcium removal service. We provide this for you at excellent cost, that way your pool can be as good as new in about a day. And it’ll stay that way for a long time of healthy leisure.


  • 0

How to Get Rid of Lime Deposits from Well Water in Your Pool

Tags : 

When calcium forms on your pool, an effect known as limescale, your pool can look unsightly and even be in danger.

If lime develops in your pool, you should hire pool maintenance professionals to inspect and clean up debris from its surfaces. Most pool cleaning services make a diagnosis for the localization and the elimination of limescale.

If you want to do it yourself, read the rest of the article.

How to detect lime deposits in your Pool

Look for white or light gray spots on the sides and bottom of the pool, as well as the edges of the pool deck. Limestone forms scaly spots or streaks when the pH of the pool water and the calcium levels in the water are out of balance.

Although this build-up of lime can be removed, it can be difficult to do so. This article provides homeowners with tips that any pool maintenance company wouldn’t want you to know to remove lime deposits from the pool walls and prevent their return.

Lime stains in the pool

If you have ever noticed, you will have seen that there is a white line on the walls, at the height of the surface. This is caused by lime deposits.

In pools with well water, these lime deposits form in a short time, and if they are not removed, the layer becomes thicker and difficult to clean.

Another problem is the roughness that is noticeable on the walls, when passing the hand the touch is rough.

Over time, this texture favors the accumulation of dirt and makes cleaning more difficult.

In addition, if you apply acid to dilute the lime, you are also diluting the cement in the joints, damaging the lining, until you have to empty the pool to repair it.

What if you use well water for your pool?

On many occasions, especially in pools installed in rural areas, there is no access to running water, so there is no choice but to use well water to fill the pool.

Well, I have a trick to remove lime from the pool with well water.

Well water treatment

This trick is not for everyone. It is not difficult to apply, but you have to be careful to follow the steps correctly.

If the pool is already affected by the remains of lime, you should lower the pH as much as possible, adding a lot of acid, or liquid pH-.

With a pH lower than 6, the lime will start to thin, but so will the cement joints.

It is VERY IMPORTANT that no one takes a bath during the process. The acidity of the water will be very aggressive for people.

After a few days in this state, empty the pool completely, clean the surfaces well with acid (better to use a specific liquid or pH reducer based on sulfuric acid, because hydrochloric acid or sulfonate emits a lot of vapors). Finally, you will have to re-grout (apply Borada or seal with cement) all the joints.

As you can see, it is slow and hard work, and it is better to do it out of season, to avoid the effects of heat on the empty pool.

With the pool empty, the next step is filling (you probably already guessed that).

Start filling it by adding shock bleach.

The well water contains a lot of organic matter, is very “alive”, and then the plant matter, such as algae, begin to react to the light of the sun. Water can go bad in a matter of hours. Sometimes the same water is already green. Don’t worry about adding more chlorine than necessary, while no one takes a bath.

How to purify well water

Now comes the secret.

Add flocculant to the water. Yes, it’s that easy, but wait, this is just the beginning.

The flocculant causes all elements other than water to stick together, forming solid “flakes” (flocs) that settle to the bottom of the pool or remain stuck in the sand filter.

Be very careful not to overdo the dose of flocculant, because the sand can stick, and you will have to replace it.

calcium removal calcium killer

You will have to do sand washes every few hours so that the sediment is expelled.

These remains will include lime, algae, metals, and other elements.
The water will be practically pure. You will also have to help by sweeping the bottom so that the dirt does not stay there.

You can increase the effectiveness by adding a layer of diatomaceous earth, or diatomaceous sand over the filter sand, to retain a greater amount of debris.

Anyway, think that diatomite is difficult to find and somewhat expensive, so it is not necessary to use it unless you want to do a cleaning worthy of an operating room.

Most of it will go down the drain when doing a sand wash, so this is disposable.

The process time will depend on the type of water you are treating, so you will have to experiment and observe.

You can also repeat the process after a few days. However, it is better to do it before adding salt, in salt chlorination systems.

Types of Calcium that Leave Deposits

There are 2 common types of calcium that form lime in a pool: calcium carbonate and calcium silicate. It is important to understand which type harms the walls of your pool.

The calcium carbonate is white, scaly and easily detached. Calcium silicate is slightly gray and more solid, which makes it more difficult to remove.

If the walls of your pool contain calcium silicate, the scale on the walls of your pool is a symptom of a more serious problem: calcium scale in the plumbing and filtration system. This is a problem that only a professional pool maintenance company can deal with.

If you don’t know what type you have on your pool, use a dropper to pour muriatic acid on the deposits. Calcium carbonate will foam in reaction to acids. Calcium silicate, being a more solid substance with robust construction, will remain unchanged.

Removing Calcium Carbonate

If your pool contains calcium carbonate, removing it is easy, but takes time.

You can use a rough but harmless object for tiles such as a wet pumice stone or an eraser to flake off deposits.

You can also get calcium descaling treatment solutions from a pool service company or a pool supply store. Follow the product instructions to avoid damaging the pool water or injuring yourself.

Removal of Calcium Silicate

Calcium silicate is incredibly difficult to remove on your own. You can try using a pumice stone, but it will take a ton of elbow grease and time to complete the process successfully.

If you have a vinyl or fiberglass pool, this will not work at all. Even some descaling treatments can take months to break down the lasting calcium silicate.

You will probably need to hire pool maintenance professionals to remove lime build-up if you cannot do it yourself. They can also adjust the quality of your pool water, including pH and calcium levels, to prevent future buildup.

Remove limestone with a blowtorch and a polishing machine

If you have emptied your pool to clean it and you notice traces of lime, there are two methods that can get rid of this debris. These methods are effective but can take a long time depending on the size of your pool.

To remove the lime that is in the walls of your pool, just use a blowtorch to make the tartar less robust and then rub it with a wire brush. With the effect of heat, the tartar will be easily removed.

If you have limestone at the bottom of the pool, simply clean the pool thoroughly with a vacuum cleaner, then sand it with a sanding and polishing machine.

Once descaling and polishing are finished, rinse your pool with a karcher to remove debris. Then evacuate your pool, let it dry, and fill it again if you want to reuse it.

If you do not want to fill it immediately, choose a tarpaulin or a protective cover. Your pool will therefore remain intact and ready to be filled at any time you wish.

Good to know

The disadvantage of chlorine is that it makes no difference between organic impurities and the human body. The consequences after a long stay in the water are red eyes, caused by chlorine. This is the reason why most people wear swimming goggles.


  • 0

How to Remove Ugly Limescale from Pool Tile Surface and Joints

Tags : 

When it comes to your body, calcium is a very good thing, but when it comes to your pool, it is not. When calcium forms on your pool, an effect known as limescale, your pool can look unsightly and even be in danger.

If lime develops in your pool, you should hire pool maintenance professionals to inspect and clean up debris from its surfaces. Most pool cleaning services make a diagnosis for the localization, as well as the elimination of limescale.

If you want to do it yourself, read the rest of the article.

So how do you know if your pool contains lime deposits?

Look for white or light gray spots on the sides and bottom of the pool, as well as the edges of the pool deck. Limestone forms scaly spots or streaks when the pH of the pool water and the calcium levels in the water are out of balance.

Although this build-up of lime can be removed, it can be difficult to do so. This article provides homeowners with tips that any pool maintenance company wouldn’t want you to know to remove lime deposits from the pool walls and prevent their return.

Lime stains in the pool

If you have ever noticed, you will have seen that there is a white line on the walls, at the height of the surface. This is caused by lime deposits.

In pools with well water, these lime deposits form in a short time, and if they are not removed, the layer becomes thicker and difficult to clean.
Another problem is the roughness that is noticeable on the walls, when passing the hand the touch is rough.

Over time, this texture favors the accumulation of dirt and makes cleaning more difficult.

In addition, if you apply acid to dilute the lime, you are also diluting the cement in the joints, damaging the lining, until you have to empty the pool to repair it.

What if you use well water for your pool?

On many occasions, especially in pools installed in rural areas, there is no access to running water, so there is no choice but to use well water to fill the pool.

Well, I have a trick to remove lime from the pool with well water.

Well water treatment

This trick is not for everyone. It is not difficult to apply, but you have to be careful to follow the steps correctly.

If the pool is already affected by the remains of lime, you should lower the pH as much as possible, adding a lot of acid, or liquid pH-.

With a pH lower than 6, the lime will start to thin, but so will the cement joints.

It is VERY IMPORTANT that no one takes a bath during the process. The acidity of the water will be very aggressive for people.

After a few days in this state, empty the pool completely, clean the surfaces well with acid (better to use a specific liquid or pH reducer based on sulfuric acid, because hydrochloric acid or sulfonate emits a lot of vapors).
Finally, you will have to re-grout (apply Borada or seal with cement) all the joints.

As you can see, it is slow and hard work, and it is better to do it out of season, to avoid the effects of heat on the empty pool.

With the pool empty, the next step is filling (you probably already guessed that).

Start filling it by adding shock bleach.

The well water contains a lot of organic matter, is very “alive”, and then the plant matter, such as algae, begin to react to the light of the sun. Water can go bad in a matter of hours. Sometimes the same water is already green. Don’t worry about adding more chlorine than necessary, while no one takes a bath.

How to purify well water

Now comes the secret.

Add flocculant to the water. Yes, it’s that easy, but wait, this is just the beginning.

The flocculant causes all elements other than water to stick together, forming solid “flakes” (flocs) that settle to the bottom of the pool or remain stuck in the sand filter.

Be very careful not to overdo the dose of flocculant, because the sand can stick, and you will have to replace it.

calcium removal calcium killer

You will have to do sand washes every few hours so that the sediment is expelled.

These remains will include lime, algae, metals, and other elements.
The water will be practically pure. You will also have to help by sweeping the bottom so that the dirt does not stay there.

You can increase the effectiveness by adding a layer of diatomaceous earth, or diatomaceous sand over the filter sand, to retain a greater amount of debris.

Anyway, think that diatomite is difficult to find and somewhat expensive, so it is not necessary to use it unless you want to do a cleaning worthy of an operating room.

Most of it will go down the drain when doing a sand wash, so this is disposable.

The process time will depend on the type of water you are treating, so you will have to experiment and observe.

You can also repeat the process after a few days. However, it is better to do it before adding salt, in salt chlorination systems.

Types of Calcium that Leave Deposits

There are 2 common types of calcium that form lime in a pool: calcium carbonate and calcium silicate. It is important to understand which type harms the walls of your pool.

The calcium carbonate is white, scaly and easily detached. Calcium silicate is slightly gray and more solid, which makes it more difficult to remove.

If the walls of your pool contain calcium silicate, the scale on the walls of your pool is a symptom of a more serious problem: calcium scale in the plumbing and filtration system. This is a problem that only a professional pool maintenance company can deal with.

If you don’t know what type you have on your pool, use a dropper to pour muriatic acid on the deposits. Calcium carbonate will foam in reaction to acids. Calcium silicate, being a more solid substance with robust construction, will remain unchanged.

Removing Calcium Carbonate

If your pool contains calcium carbonate, removing it is easy, but takes time.

You can use a rough but harmless object for tiles such as a wet pumice stone or an eraser to flake off deposits.

You can also get calcium descaling treatment solutions from a pool service company or a pool supply store. Follow the product instructions to avoid damaging the pool water or injuring yourself.

Removal of Calcium Silicate

Calcium silicate is incredibly difficult to remove on your own. You can try using a pumice stone, but it will take a ton of elbow grease and time to complete the process successfully.

If you have a vinyl or fiberglass pool, this will not work at all. Even some descaling treatments can take months to break down the lasting calcium silicate.

You will probably need to hire pool maintenance professionals to remove lime build-up if you cannot do it yourself. They can also adjust the quality of your pool water, including pH and calcium levels, to prevent future buildup.

Remove limestone with a blowtorch and a polishing machine

If you have emptied your pool to clean it and you notice traces of lime, there are two methods that can get rid of this debris. These methods are effective but can take a long time depending on the size of your pool.

To remove the lime that is in the walls of your pool, just use a blowtorch to make the tartar less robust and then rub it with a wire brush. With the effect of heat, the tartar will be easily removed.

If you have limestone at the bottom of the pool, simply clean the pool thoroughly with a vacuum cleaner, then sand it with a sanding and polishing machine.

Once descaling and polishing are finished, rinse your pool with a karcher to remove debris. Then evacuate your pool, let it dry, and fill it again if you want to reuse it.

If you do not want to fill it immediately, choose a tarpaulin or a protective cover. Your pool will therefore remain intact and ready to be filled at any time you wish.

Good to know

The disadvantage of chlorine is that it makes no difference between organic impurities and the human body. The consequences after a long stay in the water are red eyes, caused by chlorine. This is the reason why most people wear swimming goggles.

Here’s a video that summarizes all we’ve said:


Calcium Gone

Call us when you want the calcium gonecalcium removal calcium killer

Tap Here to Call and speak to the expert in calcium.

pool tile cleaning,cleaning pool tile,Pool tile cleaner,swimming pool tile cleaning,cleaning calcium on pool tile,cleaning swimming pool tile,swimming pool calcium tile cleaning,cleaning white stuff on pool tile,white stuff on my pool tiles,calcium pool tile cleaning,cleaning calcium on my swimming pool tile,white stuff on my pool tiles,how to clean off calcium on my pool,calcium cleaning

Quick Contact Form

    Your Name (required)

    Your Phone # (required)

    Your Email (required)

    Subject

    Your Message

    Enter In these letters / numberscaptcha
    In to this box to prove your real...

    Swimming Pool Tile Cleaning | Calcium Cleaning | Cleaning Pool Tile Services - Just One Call To The Pool Tile Cleaner Pro Get's The White Stuff GONE!

    Specialties Aquatic Tile Cleaning GPS Directions